|
|
| |
AMF ( Auto Mains Failure ) Controllers is for controlling the Diesel Generator, When Mains fail, this controller Automatically gives start kick to Diesel Generator, If the Generator does not start after 3 Kick, then it gives the Hooter Output. If the Generator starts then the Load is transferred to Generator. Meanwhile if the Mains recovers the load is transfered to the Mains after Delay. And D.G is kept ON for 1 Minute for cooling and then the controller
gives Stop Output |
| |
If there is any Fault Detected then it stops the D.G |
| |
Optional: Load High and Load Low this inputs are used for connecting two D.G in Load Sharing Mode .If there is Low load then slave D.G is Stopped, if Load is High then the Slave D.G is made ON to share the Load. |
|
| |
|
| |
|
| |
|
|
Specifications : |
|
Controller Detects inputs as follow. |
|
|
Digital Inputs Active Low |
|
Relay Outputs 2 Potential Free and 3 Outputs - 12/24Volts |
|
Supply Voltage 12-24 Volts |
|
LCD Display 16x2 |
|
4 Keys |
|
Battery Voltage |
|
RPM indicator |
|
Frequency indicator |
|
DG running hour display |
|
Fully Microcontroller Based System |
|
| |
|
|
Mains OK via MON Input Active Low. |
|
D.G ON Via DON. |
| |
|
| |
Faults Inputs as |
|
High temperature Fault Via HCT |
|
Oil Pressure fault via LLOP |
|
Over Load Fault via (OL) |
|
Overspeed Fault via (OS) |
|
Diesel Tank Empty via (D.T) |
| |
|
| |
For Two D.G interface Inputs in load sharing mode |
|
Load High (Hi)
|
|
Load Low (Lo) |
|
|
|
| |
|
| |
|
| |
|
 |
| |
|
| |
|
|
|
| |
We at EXTREME AUTOMATION are into manufacturing Universal Controllers and consultancy and services in design and development.
This controller software will be developed as per your requirements. This controller can be used as a replacement for PLC at a lower cost. |
|
| |
|
| |
|
| |
|
| |
|
| |
|
|
| |
|
| |
|
|
|
|
9 Digital Inputs Active Low |
|
5 Relay Outputs 2 Potential Free and 3 Outputs - 12/24Volts |
|
Supply Voltage 12-24 Volts |
|
LCD Display 16x2 |
|
4 Keys |
|
|
Packaging Machines |
|
AMF Panels |
|
Special Purpose Machines |
|
Batching Plants |
|
Whereever PLC is needed |
|
Any Automation or Process control as per requirement. |
|
|
|
| |
|
|
|
|
|
|
| |
|
| |
|
|
|
| |
3phase Volt/Amp/Freq (Vif) |
|
|
|
Microcontroller based System.
|
|
Voltage Range: upto 500Volt |
|
Current Range: upto 5000Amps
for 5000/5 CT |
|
Frequency Range: 10Hz to 100Hz |
|
Over/Under Voltage Settable. |
|
Manual /Auto Reset for overload |
|
OverLoad current settable |
|
Password Protection for Calibration |
|
Relay Output for Overload |
|
Relay Output For Over/Under voltage |
|
Auto Scrolling / Manual Select Mode of Display |
|
Single Phasing |
|
|
| |
|
|
| |
|
|
| |
Applications |
|
Used in Panel |
|
General Purpose Application |
|
Used for load check |
|
3 Phase Voltage Display |
|
Over Voltage Trip |
|
3 Phase Current Display |
|
Under Voltage Trip |
|
Frequency Display |
|
Used as Home Protector |
|
Under Voltage /Over Voltage Trip Output |
| |
|
|
OverLoad Trip Output |
|
|
| |
|
|
|
|
|
|
|
| |
|
| |
|
|
Auto Load Sharing Controllers (ALS) |
|
| |
This is a Automatic Load Sharing Controller, which computes load current of Two Diesel Generator (DG) Sets and if the Load is less and can be handled by the Master Diesel Generator (DG) it will put off the Slave Diesel Generator (DG) to Save the FUEL. Three C.T.s for 3 Phase fo Master DG and Three C. T. s for Slave DG is connected which measures the current. The display shows each phase current one by one of DG 1 and DG 2. |
| |
|
|
| |
|
Specifications : |
|
|
|
LOW COST SOLUTION for D.G. Syncronization Units. |
|
C.T. Ratio is from 50 to 1000 |
|
Microcontroller Based Design |
|
ALS O/P - Slave DG Start & Slave DG stop |
|
ALS I/P - 6 C.T.s |
|
Delay Provided for Averaging of Load Current to minimise switching of DG |
|
|
Power I/P 230 VAC from master DG |
|
1 Amps Resolution for 500 Amps C.T. ratio |
|
When the Load is High, ALS Shows the Load High Indication |
|
Displays frequency of the Master DG |
|
C. T. Ratio is programable for Both Master and Slave Dgs |
|
Size - 96 X 96 pannel mounted |
|
|
|
|
|
|
|
|
|
| |
|
Temperature Monitoring Systems
|
| |
|
| |
|
|
|
| |
|
|
Temperature Recording Facility, total Readings which can be stored in the instrument is 4,500 for 8 channel. |
|
Time and Date Display on 16x2 LCD Display |
|
Battery Backup, for 6Hrs, for Eight Sensors. |
|
Over/Under Range Buzzer and LED Indicator. |
|
Spikes protection inbuilt |
|
Sensor module can be remotely connected to
450 mtrs.for distributed applications |
|
|
Auto Dialing Facility for Over Range and Under Range Detection. |
|
Rs232 serial Communication for PC |
|
PT100 Sensors. Temperature Range is -100 to +100 or 0 to 200 . |
|
1 °C/ 0.1 °C Temperature resolution |
|
Operating voltage: 230VAC |
|
Dimension: 192mmx96mmx200 |
|
|
|
| |
|
|
|
|
| |
Software |
|
|
|
|
|
Alarm, Under Range / Over range Limits Can be set from the Computer. |
|
Reading Downloaded can be viewed and Printing Facility, and Displayed in Graphical Format, for analysis. |
|
Sampling/Recording Time settable from the Computer. |
|
Auto dialing Phone number settable from the computer. |
|
Readings can be searched and displayed Date wise. |
|
Instrument Date and Time can be set from the computer. |
|
Software compatible with Windows XP, Office2003. |
|
Phone receive ACK by pressing 123 |
|
|
|
|
|
| |
| |
|
|
|
|
|
Temperature Controller With 2 Setpoints
|
|
| |
Introduction:
This is a 4 digit Digital Temperature Indicator cum controller with single RTD input and Two relay outputs with user specified control action and relay logic. It also has an optional 4-20mA output for PLC or Microcontroller based system Interface.
|
Specification: |
Microcontroller based Design.
Input Sensor: PT100
Output: 2 Relay's NO,C,NC
Optional 4-20mA output, corresponding to Temperature.
Range: 0 to 400 DegC
Two Set Points: RL1 and RL2
Hysteresis: +/- 3 Deg C for both Set Points
Supply Voltage: 230V AC 50Hz.
Size: 96x96 Panel Mountable |
|
|
| |
|
| |
|
| |
|
| |
|
